Explosion Proof Industry Motors: How to Read an Ex Marking After IEC 60079-0:2026

Oct 14, 2026 Leave a message

In July 2026, the International Electrotechnical Commission published the eighth edition of IEC 60079-0, the general-requirements standard that sits underneath almost every piece of equipment used in explosive atmospheres. If you buy or specify explosion proof industry motors, you don't need to read the whole standard. But you do need to read the nameplate properly, and this edition changes what that nameplate has to show.

Here is how to decode a typical marking, what the new edition adjusts, and what to send a supplier before you ask for a quote.

Decode one line, left to right

Below is a generic example for illustration only. It is not taken from any specific Milestone Motor certificate.

 

 

Ex db IIB T4 Gb

 

Ex: the equipment is certified for explosive atmospheres.

d: the protection method is a flameproof enclosure. The housing is built to contain an internal explosion and stop it reaching the surrounding atmosphere. The second letter, b, is the level of protection.

IIB: the gas group the motor is suited to. A motor marked IIB can be used where IIB or IIA gases are present, but not where the site needs IIC. Typical IIB gases include ethylene; IIC covers hydrogen and acetylene.

T4: the temperature class. No surface of the motor may exceed 135 °C in rated operation or specified fault conditions. The ignition temperature of the gas on your site must sit above that limit.

Gb: the equipment protection level for gas, which corresponds to Zone 1, where an explosive gas atmosphere may occasionally occur in normal operation.

For dust sites the marking uses a different pattern, such as Ex tb IIIC with a surface temperature and a "Db" protection level. The logic is the same: method, group, temperature, level.

 

What Edition 8 changes at the nameplate

 

According to SGS and ExVeritas, who both published summaries after the release, several changes touch the information a buyer sees:

  • Ambient temperature must always be marked, even when the range is the familiar -20 °C to +40 °C. Previously a standard range could be left off.
  • IP rating marking has been clarified, and the temperature range of an Ex component must now appear in the schedule of limitations.
  • Digital alternatives for marking Ex equipment are now addressed, so QR-style marking will be treated more formally.
  • Motors are specifically affected. There are additional requirements for the instructions supplied with converter-driven Ex e motors, and the requirements for motors tested with a converter have been modified.

For most buyers, the practical effect is simple: a compliant nameplate and documentation pack will carry more information than before, and gaps are easier to spot.

 

What it does not mean

 

It does not make existing motors illegal. ExVeritas notes that under grandfathering, products already certified keep their certification against the previous edition. If a supplier offers you a motor certified to Edition 7, that is not automatically a red flag. What matters is that the certificate is valid, matches the exact model you are buying, and covers your hazardous area.

 

Four facts your supplier needs from you

 

Choosing among explosion proof industry motors is mostly a matter of passing the right facts. The selection steps on our Explosion Proof Industry Motors page walk through them; in short:

  1. Zone and substance. Is the hazard gas or dust? Which Zone (0, 1, 2 for gas; 20, 21, 22 for dust)? Which gas group?
  2. Temperature class. Pick one whose limit sits safely below your substance's ignition temperature.
  3. Site conditions. Ambient temperature, altitude, and whether the air is corrosive, salty or very humid. Thin air at altitude reduces cooling, so derating or a special design may be needed.
  4. How the motor will run. If it will be driven by a frequency converter, say so at the start. The new edition's attention to converter-driven motors is a reminder that this changes testing and documentation.

 

Where Milestone Motor fits

 

Milestone Motor is an established manufacturer in Hengshui, Hebei, and holds ISO 9001, ISO 14001 and ISO 45001 management system certifications. Its explosion-proof range includes flameproof motors, Ex proof motors and explosion proof pump motors.

Whichever supplier you choose, ask for the same things: the certificate for your exact model, the full marking as it will appear on the nameplate, and the installation and maintenance instructions. If you'd like Milestone Motor to review your zone, gas group and operating conditions before you decide, send them through the inquiry page.

Contact now

 

Sources: SGS, "IEC 60079-0:2026 – Significant Technical Changes" (July 2026); ExVeritas, "Changes to IEC/EN 60079-0 as Edition 8 is introduced" (August 3, 2026).

Send Inquiry

Home

Phone

E-mail

Inquiry